- PATCH 1 SEPARATOR HOW TO
- PATCH 1 SEPARATOR PDF
- PATCH 1 SEPARATOR DRIVER
- PATCH 1 SEPARATOR PATCH
- PATCH 1 SEPARATOR SOFTWARE
This section describes how to use patchcode sheets with CapturePerfect 3.1. The image of this sheet is saved regardless of the application's settings. When the scanner recognizes this patchcode printed on a patchcode sheet, it creates a separate file starting from the patchcode sheet. The image of this sheet is saved or not saved, depending on the application's settings. When the scanner recognizes this patchcode printed on a patchcode sheet, it creates a separate file for the document that comes after the patchcode sheet. There are two types of patchcodes, and their function changes according to their pattern. If a patchcode sheet has been folded or becomes creased, reprint or replace the sheet.
The scanner may not recognize them as patchcode sheets if they are enlarged or reduced. Patchcode sheets must be printed in their original size.
PATCH 1 SEPARATOR PATCH
PATCH 1 SEPARATOR PDF
Open the desired patchcode sheet file with CapturePerfect 3.1 or an application that supports the PDF file format, and print the page image only at its original size. There are four types:, ,, , organized according to the paper size and pattern. Patchcode sheets are available in PDF format.Patchcode sheets can be used only when the application you are using supports separating files by patchcode patterns.In Windows 8, the batch code sheets are saved to the applications table.
PATCH 1 SEPARATOR DRIVER
Patchcode pattern icons are registered in the following location when the ISIS/TWAIN driver is installed. Patchcode patterns are printed on the patchcode sheets used to automatically separate files. Patch types 1, 4 and 6 are not used for document separation but to enable other features such as colour or multifeed detection.When the optional patchcode decoder is installed, the DR-G1130/G1100 supports Automatic File Separation by detecting patchcode sheets inserted within a document, and performs batch separation. Typically patch Type 2 is used for Document Separation, Type 3 for Batch Separation and Type T can be used for either Document or Batch Separation.
PATCH 1 SEPARATOR SOFTWARE
The exact action taken on recognising a patch code will depend upon the system and software used, and may be configurable in a given application. It is possible to incorporate a patch code into a form (typically a Patch 2 code on the first page of the form), to indicate a new file should be started for each form. It is also possible to add conventional barcodes (typically Code 39) to a sheet to, for example, indicate the document type. Similarly although there may be 4 identical patch codes on a page (one in each orientation) patch code readers (hardware or software) would only ever return one. Note that no data is encoded in a patch code. A common use now is to use the Patch T code or the Patch 2 code as a Page (document) separator. Six distinct barcode patterns (Patch 1, 2, 3, 4, 6 and T) were defined. The different codes will signal certain events such as a page/section break or a change from single sided to duplex scanning. The patch code was originally created by Kodak to signal document processing applications while reading large documents. Some scanners (such as the Kodak i800) require the patch code to be printed parallel to the feed-edge, other scanners (such as the Kodak i5000) require the patch code to be perpendicular (at right angles) to the feed-edge.Ī typical use of a patch code is distinguish where one document ends and another begins when a pile of documents are loaded into the sheet-feeder (ADF) of a document scanner. For this reason patch codes are often printed on all four edges of the page.
This will vary depending upon the model of scanner used, and the orientation of the page. Exactly what action is taken depends upon the design of any given system.Ī patch code needs to be printed in a certain position, usually near the leading edge (feed-edge) of the document. The patch code may be recognised by the scanner itself (more usually in the top-end expensive scanners) or by the scanning or processing software or with a TWAIN or ISIS driver. When scanning the document the patch code can be recognised and acted upon.
Patch codes are a set of 6 distinct barcode patterns (1, 2, 3, 4, 6 and T) that are typically used as document separators when scanning.Ī patch code is a pattern of parallel, alternating black bars and spaces (a barcode) that is printed on a document.